ISO 12 ga AE forend 29890

This forum is to be used to post A.H. Fox Gun parts and pieces from orphaned guns you own or you are searching for. This forum is NOT to be used to sell ANYTHING including complete guns or gun parts. This forum is NOT a marketplace but a bulletin board. All contacts between individuals are to be made through the forum PM system. No prices are to be posted. The main intent here is to marry parts with the original gun and to celebrate that reunion.
Post Reply
ShepFL
Posts: 5
Joined: Wed May 21, 2014 4:12 pm
Been thanked: 9 times

ISO 12 ga AE forend 29890

Post by ShepFL »

Like most looking for complete iron for ejector gun. Auction gun that is missing entire forend. Will be restocking so wood not critical.
Located in N Florida
Thanks in advance
Top
bbman3
Posts: 1629
Joined: Fri Jan 05, 2007 10:13 pm
Location: Deep South
Has thanked: 184 times
Been thanked: 122 times
Contact:
Contact bbman3

Re: ISO 12 ga AE forend 29890

Post by bbman3 »

Have seen a couple on ebay in the past years. Bobby
Top
ShepFL
Posts: 5
Joined: Wed May 21, 2014 4:12 pm
Been thanked: 9 times

Re: ISO 12 ga AE forend 29890

Post by ShepFL »

Thank you sir. I am looking at one now that has set of 32" barrels also. I do know of a nice early A forend but holding off right now until I open her up to see what else is needed. Momma don't mind me going to the well but only 1x. Have to be frugal with my $$ and this "sxs affliction" can sometimes be spendy.
Top
ShepFL
Posts: 5
Joined: Wed May 21, 2014 4:12 pm
Been thanked: 9 times

Re: ISO 12 ga AE forend 29890

Post by ShepFL »

Found my parts so now the journey begins. Should be here next week. Will post pics.
Top
Foxnut
Posts: 1635
Joined: Tue Jan 16, 2007 11:53 pm
Location: Western, MI
Has thanked: 769 times
Been thanked: 845 times

Re: ISO 12 ga AE forend 29890

Post by Foxnut »

ShepFL, keep us posted on the project and work progress!
Regards - Foxnut
Top
ShepFL
Posts: 5
Joined: Wed May 21, 2014 4:12 pm
Been thanked: 9 times

Re: ISO 12 ga AE forend 29890

Post by ShepFL »

NOS parts have arrived. That was a wild goose chase. Now the work begins.
Attachments
20230407_162332.jpg
Top
ShepFL
Posts: 5
Joined: Wed May 21, 2014 4:12 pm
Been thanked: 9 times

Re: ISO 12 ga AE forend 29890

Post by ShepFL »

Foxnut wrote: ↑Sun Apr 02, 2023 11:16 am ShepFL, keep us posted on the project and work progress!
Going down another path. Wife bought me some nice wood so chasing a 20 ga Fox that needs restocked if I can find one.
The 12 ga AE is sitting on the bench - hurricanes last fall took a toll on friends in NE TN and sister in law in St. Pete Beach.
Been helping folks get back into their house if it is still there.
Watch for updates mid-summer before fall arrives.
Attachments
ae wood-1.png
ae wood-3.png
Top
Foxnut
Posts: 1635
Joined: Tue Jan 16, 2007 11:53 pm
Location: Western, MI
Has thanked: 769 times
Been thanked: 845 times

Re: ISO 12 ga AE forend 29890

Post by Foxnut »

That is indeed some nice wood. Sounds like you’ve had a lot of “irons in the fire”. Hope your family is getting back into homes or getting repairs as needed.
Regards - Foxnut
Top
Post Reply

Return to “Fox Parts and Pieces, Lost and Found”