New to the Forum - Need General Restoration Advice

Post your questions or seek advise regarding gunsmithing, restoration, repairs, ballistics, etc, etc.
Commercial operations or businesses may not advertise nor appear to advertise their products or services, either directly, or indirectly by a second party, except for simple reference as a source for such products or services

New to the Forum - Need General Restoration Advice

Postby Farmboy76 » Thu Apr 23, 2020 12:14 pm

Hi everyone - hope you are all safe during these uncertain and strange times. My father gave me some old shotguns he had lying around and the most beautiful was a Fox Sterlingworth. I'd never heard of that manufacturer, but did a little research and found your forum. I'm thrilled this beautiful firearm has such rich history and robust following. I have lots of time on my hands being stuck inside and was hoping to make use of it by refinishing the stocks and barrels on these scatterguns (something I've not attempted before). While the Fox gun won't be the first I try to refinish, I did want to seek out more knowledgeable folks on this specific firearm and inquire about its provenance, age, and potential value. I've been around firearms for many years and have an amateur coin collection, so I know the first thing NOT to do when you find a beautiful collectible piece is go vigorously wipe away the patina or original finishes. Is this Fox gun more valuable/authentic as-is? I'd love to keep it as my own for a long time and the idea of refinishing it is incredibly exciting to me, but if the general consensus is that it's better with the finish it currently has, I don't want to inadvertently destroy that. Any and all advice is appreciated in advance! (Pictures for reference attached)

Thanks again and stay safe
Attachments
IMG_0023.jpg
Serial No.: 123216
IMG_0022.jpg
Accumulated rust
IMG_0021.jpg
IMG_0020.jpg
Finish on stock
IMG_0019.jpg
Farmboy76
 
Posts: 1
Joined: Wed Apr 22, 2020 10:25 pm

Re: New to the Forum - Need General Restoration Advice

Postby Jim Cloninger » Thu Apr 23, 2020 12:28 pm

If that was my gun, all I would do is restore the stock. Jim
Goodbye Mandy, once in a life time hunting dog. I miss you every day.
Jim Cloninger
 
Posts: 1320
Joined: Wed Jul 25, 2007 12:14 pm
Location: West

Re: New to the Forum - Need General Restoration Advice

Postby Jeff S » Thu Apr 23, 2020 12:58 pm

I'm with Jim. Refinishing the stock would make it a dandy gun. Have fun!
User avatar
Jeff S
 
Posts: 1665
Joined: Tue Jan 06, 2015 11:59 am
Location: Grand Rapids, Michigan

Re: New to the Forum - Need General Restoration Advice

Postby jolly bill » Thu Apr 23, 2020 11:41 pm

If you do refinish the wood, go easy with the sand paper. Especially around where the wood interfaces with the receiver, trigger guard and fore end iron. Leave the butt plate on when you (lightly) sand that part of the stock.

Nice looking gun.

PS: Welcome.
jolly bill
 
Posts: 1074
Joined: Sun Jan 21, 2007 11:06 pm
Location: Western NY

Re: New to the Forum - Need General Restoration Advice

Postby Brian Dudley » Mon Apr 27, 2020 9:56 am

The gun has a lot of good going for it and only needs sympathetic cleanup and mild restoration to the wood finishes. If it were not for the amount of flaking in the finish on the wood, I would say just leave it alone. However, if you do not have experience in proper restoration of wood on guns, then you should leave it alone. There is a fine line on a gun like this between doing it right and screwing it up.
,Brian Dudley
Brian Dudley
 
Posts: 195
Joined: Fri Aug 17, 2012 3:09 pm
Location: Rochester, NY

Re: New to the Forum - Need General Restoration Advice

Postby Stan Hillis » Wed Apr 29, 2020 7:44 am

First, welcome to the forum.

I'm in total agreement with Brian, who has much more experience with this than most of us, as he is an active vintage doublegun 'smith. I have a Sterly with the same condition wood, and have never touched it for fear of doing it wrong.

Best, SRH
Stan Hillis
 
Posts: 1972
Joined: Sun Nov 09, 2008 9:31 pm
Location: Jawja


Return to "Technicana" and Restoration Forum

Who is online

Users browsing this forum: No registered users and 1 guest